B6 Cylinder Head Coolant Pipe Connections Page 22: cooling system cooling system audi q7 4 .2l v8 fsi cooling system heater core expansion tank coolant temperature sensor t° generator coolant pump radiator oil cooler thermostat 377 030 the cooling system in the new v8 engines was configured a map controlled coolant thermostat is used in the basic as a longitudinal flow cooling system. B6 s4 cooling system. hello and welcome to the audizine forums! as a guest, you are welcome to poke around and view the majority of the content that we have to offer, but in order to post, search, contact members, and get full use out of the website you will need to register for an account. it's free and it's easy, so don't hesitate to join the.
Audi A4 Coolant System Diagram Hanenhuusholli So here goes: this is the easiest and less messy way to do a complete coolant system flush (with heater core). drain coolant. 1. jack front end of car up enough to fit a bucket under the car, on the left side of the radiator core. 2. place bucket under the lower radiator hose at the core. 3. The procedure is as follows: 1.drain all coolant (there are two drain ***** on the block l r sides). 2.remove oil filter. 3.remove alternator belt, alternator and plastic breather. 4.undo swaybar from passenger side (loosen drivers side) 5 remove passenger side rear engine support (unplug wire from it first), and bracket. S4 v8 4.2l (bhf) (2004) > audi workshop service and repair manuals > engine, cooling and exhaust | cooling system | sensors and switches cooling system | engine coolant temperature sensor switch | temperature sensor (gauge) | component information | locations. Take both off (don't loose the gaskets, copper ring on the allen plug, rubber on the phillips plug), and have the 2 pales ready. 4. take off the coolant reservoir cap and watch about 7l of coolant mix come out. yes, this is a 12l in the 4.2l engines. therefore, flushing is needed in step 6. 5. put the 2 plugs back on.
The Ultimate Guide Audi A4 1 8t Cooling System Diagram Explained S4 v8 4.2l (bhf) (2004) > audi workshop service and repair manuals > engine, cooling and exhaust | cooling system | sensors and switches cooling system | engine coolant temperature sensor switch | temperature sensor (gauge) | component information | locations. Take both off (don't loose the gaskets, copper ring on the allen plug, rubber on the phillips plug), and have the 2 pales ready. 4. take off the coolant reservoir cap and watch about 7l of coolant mix come out. yes, this is a 12l in the 4.2l engines. therefore, flushing is needed in step 6. 5. put the 2 plugs back on. Rear coolant line coolant hose connection diagram page 19 9 9 lifting eye 10 10 nm (7 ft lb) 11 coolant line coolant hose connection diagram page 19 9 12 front coolant hose coolant hose connection diagram page 19 9 13 sealing cap check using vag1274 cooling system tester with vag1274 8 adapter test pressure: 1.4 1.6 bar (20 23 psi) pa. The first member of the family was the 3.2 litre v6 fsi engine. the 4.2 litre v8 fsi engine is also a member of this family. page 4: table of contents vacuum hoses in the audi rs4 page 5 system overview, audi q7 (bosch med 9.1.1) 36 system overview, audi rs4 (bosch med 9.1) 38 operating modes . page 6: introduction.
Audi A4 S4 Avant Qu 2005 2008 Coolant Cooling System Vag Etka Rear coolant line coolant hose connection diagram page 19 9 9 lifting eye 10 10 nm (7 ft lb) 11 coolant line coolant hose connection diagram page 19 9 12 front coolant hose coolant hose connection diagram page 19 9 13 sealing cap check using vag1274 cooling system tester with vag1274 8 adapter test pressure: 1.4 1.6 bar (20 23 psi) pa. The first member of the family was the 3.2 litre v6 fsi engine. the 4.2 litre v8 fsi engine is also a member of this family. page 4: table of contents vacuum hoses in the audi rs4 page 5 system overview, audi q7 (bosch med 9.1.1) 36 system overview, audi rs4 (bosch med 9.1) 38 operating modes . page 6: introduction.
Comments are closed.