Bleeding The Coolant System On A Jeep Liberty Locate the radiator drain valve on the bottom of your jeep liberty’s radiator. place a coolant catch container under the valve to collect any excess coolant and open the valve using a flat head screwdriver. allow all the coolant to fully drain, then close the valve once you have finished. disconnect and remove any hose or plugs from your. 3. reaction score. 0. tjkj2002 said: pressure or no pressure at some point the trapped air pocket will make it's way to the highest point.those tricky cooling systems (anything with the 4slow in it,and most gm's) i use the no spill funnel and run (no pressure) till boilover,plug funnel and turn off engine (builds pressure),wait 2 3 mins (cools.
Bleeding The Coolant System On A Jeep Liberty Had no heat because ther was air in the coolant system and low on coolant. Lisle 24680 spill free funnel is the only way i use to bleed cooling systems, it simply works. crank the heat to full open and let idle till the thermostat opens at least once. you can pump the hoses during that time carefully and help speed up the process but still wait till the stat opens. reply like. Fill system using a 50 50 mixture of ethylene glycol antifreeze and low mineral content water, until coolant begins coming out of the cooling system bleed hole. install the cooling system bleed plug. fill radiator to top and install radiator cap. add sufficient coolant to the reserve overflow tank to raise level to full mark. 2. So get home, jack the front up or park the front on a set of ramps, let it cool. take the rad cap off and start and get to temp, squeeze the top hose a few times wait for level to drop. add antifreeze as needed. let jeep sit over night and do again in the morning. do again in the afternoon if you can or the next night.
How To Bleed Coolant System On 2008 Liberty No Heat Youtube Fill system using a 50 50 mixture of ethylene glycol antifreeze and low mineral content water, until coolant begins coming out of the cooling system bleed hole. install the cooling system bleed plug. fill radiator to top and install radiator cap. add sufficient coolant to the reserve overflow tank to raise level to full mark. 2. So get home, jack the front up or park the front on a set of ramps, let it cool. take the rad cap off and start and get to temp, squeeze the top hose a few times wait for level to drop. add antifreeze as needed. let jeep sit over night and do again in the morning. do again in the afternoon if you can or the next night. 673. location. white river, south africa. eddiekimberly said: i just did a top end rebuild on '02 kj sport 3.7 4x4 for blown head gaskets. while trying to bleed my cooling system, i took off the radiator cap, turned on the heater and let it run. suddenly it spit and sputtered and the coolant level dropped, i filled it back up, replaced the cap. In maintaining your cooling system, you can both bleed a radiator of excess air, and flush a radiator of old coolant. bleeding a radiator bleeding the radiator is the process of releasing the air that may become trapped in the upper portion of a2008 jeep liberty s radiator.
Burp Bleed Coolant System 4 7l Dodge Jeep How To Youtube 673. location. white river, south africa. eddiekimberly said: i just did a top end rebuild on '02 kj sport 3.7 4x4 for blown head gaskets. while trying to bleed my cooling system, i took off the radiator cap, turned on the heater and let it run. suddenly it spit and sputtered and the coolant level dropped, i filled it back up, replaced the cap. In maintaining your cooling system, you can both bleed a radiator of excess air, and flush a radiator of old coolant. bleeding a radiator bleeding the radiator is the process of releasing the air that may become trapped in the upper portion of a2008 jeep liberty s radiator.
Coolant System Bleeder Hex Screw Jeep Enthusiast Forums
Comments are closed.